jaclaz Posted January 13, 2012 Share Posted January 13, 2012 (edited) I'm on the final bit(F3 T>m0,2,2,,,,,22) and its been going for over 2 hours now.The tutorial said up to 10 mins and others said it took about 1 hour.I have the 1TB Seagate Hard drive, so is it normal for it to take this long?Wait a further 35 minutes, then unpower the thingy, test if by any chance it is now unbricked, if not re-do from start.jaclaz Edited January 13, 2012 by jaclaz Link to comment Share on other sites More sharing options...
Blackan Posted January 13, 2012 Share Posted January 13, 2012 Great.Waited, powered down, checked it. Showed up in bio, but still didn't load OS. Plugged back into working pc, did the fix for 0 LBA problem, now its working. Thank you very much. Link to comment Share on other sites More sharing options...
marcobid Posted January 16, 2012 Share Posted January 16, 2012 Thank you very much.Ho sistemato il mio Seagate Barracuda 7200.11 da 500gb recuperando tutti i dati.La Seafate mi ha chiesto per la riparazione del disco dalle 800 alle 1.300 euro, con la tua soluzione ho speso 20 euro compreso il cacciavite Torx 6Great, Marco Link to comment Share on other sites More sharing options...
farafafafafa Posted January 17, 2012 Share Posted January 17, 2012 Hallo Y cant find the CA42 cabel,cab Y do it?whit USB cabel? please y nedd it thanks Link to comment Share on other sites More sharing options...
dsdeez83 Posted January 18, 2012 Share Posted January 18, 2012 (I'm a Newbie)Hey Guys : I've read the threads and followed the instructions for what I believe is the 0 LBA error. I ran the bios and the HD shows up so I would believe that's the case. I run through the instructions with this http://www.ebay.com/itm/280748167812?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649 tool. I'm using a firewire to USB cable. The process i follow is the same as on thread #1, I power the HD after I have the hyperterminal configured and connected. I run the "m0,2,2,0,0,0,0,22" (enter) cmd and my results similar but the User Partition says : User Partition Format Successful - Elasped Time 0 mins 00 sec. I than power down, disconnect and move the HD to the PC and power up but I still get that same error. Your assistance is grately appreicated. Link to comment Share on other sites More sharing options...
smandurlo Posted January 18, 2012 Share Posted January 18, 2012 @dsdeez83 your output is not normal, all the values in the first line are 00 and it is wrong. What was the problem? I believe you did something that ruined your access to stored data... Link to comment Share on other sites More sharing options...
dsdeez83 Posted January 18, 2012 Share Posted January 18, 2012 @dsdeez83 your output is not normal, all the values in the first line are 00 and it is wrong. What was the problem? I believe you did something that ruined your access to stored data...My problem is my Seagate 7200.11 HDD wont boot, but in BIOS is it recognized. I also set it up as a Secondary HDD and it reflects in Windows as "0". Link to comment Share on other sites More sharing options...
dsdeez83 Posted January 18, 2012 Share Posted January 18, 2012 @dsdeez83 your output is not normal, all the values in the first line are 00 and it is wrong. What was the problem? I believe you did something that ruined your access to stored data...My problem is my Seagate 7200.11 HDD wont boot, but in BIOS is it recognized. I also set it up as a Secondary HDD and it reflects in Windows as "0".I also wanted to add, I have HP24 Firmware vs some of these threads showed a seagate firmware. Link to comment Share on other sites More sharing options...
farafafafafa Posted January 19, 2012 Share Posted January 19, 2012 please I need help .I ¨m using CA42 cabel y have black GND green und white tx und rx end one red no more.I connect blacr white and green I put power to de hdd but in the hyperteminal when I write dont show anything.Need I to conect 3V, and where only have I de red.please what can I do?? Link to comment Share on other sites More sharing options...
jaclaz Posted January 19, 2012 Share Posted January 19, 2012 please I need help .I ¨m using CA42 cabel y have black GND green und white tx und rx end one red no more.I connect blacr white and green I put power to de hdd but in the hyperteminal when I write dont show anything.Need I to conect 3V, and where only have I de red.please what can I do??READ FGA's:expecially #6 AND the link givenjaclaz Link to comment Share on other sites More sharing options...
BlouBul Posted January 19, 2012 Share Posted January 19, 2012 but the User Partition says : User Partition Format Successful - Elasped Time 0 mins 00 sec. I than power down, disconnect and move the HD to the PC and power up but I still get that same error. Your assistance is grately appreicated.The only other thing I can think of that might work is to try the optional commands given by Aviko here I also wanted to add, I have HP24 Firmware vs some of these threads showed a seagate firmware.All HP firmware before HP26 suffer from the same symptoms (and uses the same fix) Link to comment Share on other sites More sharing options...
ukiahaprasim Posted January 20, 2012 Share Posted January 20, 2012 Hello.I dont understand nothing about electronics... can anyone help me?Are these converters valid for trying to unbrick my HDD?RS232 To TTL Converter Module Built-in MAX232CPE Transfer Chip With 4PCS Cableshttp://www.ebay.es/itm/RS232-To-TTL-Converter-Module-Built-in-MAX232CPE-Transfer-Chip-With-4PCS-Cables-/270845851440?pt=LH_DefaultDomain_0&hash=item3f0fabb730RS232 To TTL Converter MAX232EPE W/ Power + 4pcs cablehttp://www.ebay.es/itm/RS232-To-TTL-Converter-MAX232EPE-W-Power-4pcs-cable-/170647222229?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item27bb5df7d5MAX232EPE? MAX232CPE?...regards.Ukiah Link to comment Share on other sites More sharing options...
Huygens Posted January 20, 2012 Share Posted January 20, 2012 Are these converters valid for trying to unbrick my HDD?http://www.ebay.es/itm/RS232-To-TTL-Converter-Module-Built-in-MAX232CPE-Transfer-Chip-With-4PCS-Cables-/270845851440?pt=LH_DefaultDomain_0&hash=item3f0fabb730http://www.ebay.es/itm/RS232-To-TTL-Converter-MAX232EPE-W-Power-4pcs-cable-/170647222229?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item27bb5df7d5Both are (USB) powered with 5V, so I doubt they work, as they may end up sending a signal with too high voltage to the HD. Link to comment Share on other sites More sharing options...
dsdeez83 Posted January 21, 2012 Share Posted January 21, 2012 but the User Partition says : User Partition Format Successful - Elasped Time 0 mins 00 sec. I than power down, disconnect and move the HD to the PC and power up but I still get that same error. Your assistance is grately appreicated.The only other thing I can think of that might work is to try the optional commands given by Aviko here I also wanted to add, I have HP24 Firmware vs some of these threads showed a seagate firmware.All HP firmware before HP26 suffer from the same symptoms (and uses the same fix)So you are suggesting the extra coding in the hyperterminal? correctDrive is busy example, not solution: drive ST3500320AS SD15 remove 3 screws nearest heads connector, motor connected, put something between pcb and hda to lift pcb and prevent contact.power on, wait until drive stops motor, if you dont wait at this moment you got 000000CE error after next command(ctrl+z)F3 T>/2F3 2>ZSpin Down CompleteElapsed Time 0.146 msecsremove isolation and mount pcb as normalF3 2>USpin Up CompleteElapsed Time 6.864 secsQuotethis part is not necessary, just checking is everything ok, use when first try fails (F712 work only on 500g 7200.11 with firmware SD15, when you updated f/w just skip this partF3 2>/F3 T>F712Byte:0712: RealTimeUpdatedFlags = 00 00Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0Byte:0712: Bit:2, DCO_SET_ACTIVE = 0Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 0 <- configuration not loaded from surfaceF3 T>F,,22Drive Configuration restored to defaults.F3 T>F712Byte:0712: RealTimeUpdatedFlags = 08 00Byte:0712: Bit:0, HPA_SET_BY_SETMAX = 0Byte:0712: Bit:1, HPA_SET_BY_SETMAX_EXT = 0Byte:0712: Bit:2, DCO_SET_ACTIVE = 0Byte:0712: Bit:3, CONGEN_READ_FROM_MEDIA = 1 <- doneF3 T3>/1F3 1>N1F3 1>/F3 T>m0,2,2,0,0,0,0,22Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = 0000User Partition Format 5% complete, Zone 00, Pass 00, LBA 00008DED, ErrCode 00000080, Elapsed Time 0 mins 05 secs User Partition Format Successful - Elapsed Time 0 mins 05 secs F3 T> (finished, power off, connect disk to pc and check your data) Link to comment Share on other sites More sharing options...
BlouBul Posted January 21, 2012 Share Posted January 21, 2012 So you are suggesting the extra coding in the hyperterminal? correctCorrect Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now