Comos

Hello, Im using this card partly without problems in Win95OSR,but I noticed,that some features of this card are not working on 100% or at all.Example when I play Carmageddon 2 on full details with Direct 3D,the game is not smooth enough even with this card and with AMD-K6-III @400.When I play it on my second PC with P2@350 and with Voodoo3 through D3D,the game runs fine and smooth.Dunno why it is not fast enough on my GF4,the game requirements are not so high.Second problem is with Quake 1 when played in Win.When I change the resolution from 320x200 to higher,the game freezes.In DOS its without problems.maybe its a problem with using this newer card comaring to older game,but years ago I was testing this game on P1@ Intel233 with nVidia TNT2 and the game runs fine even on 1024x768.Another problem is in BSplayer,that I cannot enable hardware acceleration,but when I check the card with DXset ,the HW acceleration is enabled,so whats wrong?.With DXtest,some tests locks the windows,but I have to retest that.The DirectX I have,are the last working on W95OSR (8.1 I think).The Nvidia drivers are 4.09,the working ones on W95OSR,that I have tested.Or does anybody have a custom driverpack for this card? The DVD's are running through PowerDVD fine.The card has its HW MPEG2 decoding example for DVDs decoding,but can that be checked somehow,if is it used? Thanks for advice Comos

Hello, thanks for info.I'll try this one.Currently Im using the Mass Storage driver from MDGXs site,so I have to uninstall them.By now if I want to use the USB flash drive again I have to reboot...that is enough..:-)

Hello, Im expecting problems with detection of the new line of Kingston Datatraveler series especially DT110 - 2GB and DTI 8GB.I use NUSB device drivers but the system detects them wrong as USB device.I tried even the Kingstons DTI driver for a test and the result was the same.Then later I found an update for UHCD.SYS http://www.microsoft.com/downloads/details...ang=en#Overview I tried this patch on mine P2@350 with SE440BX2 chipset and I can access the DT110 with occasional problems due to wrong detection.With the DTI I didn't succeed,its detected wrong but sometimes its detected correctly and i can access it.This same problem I have on a laptop P3@650 with 443BX chipset.I applied the UHCD.SYS update and the system detect the DT110 and DTI correctly but sometimes happend that when I plug DT110,remove it from the system and then plug the DTI,the system will detect it wrong again.The installation of the Win98SE was new and these problems continue even when I tried to install the Unofiicial Service pack for Win98SE. Is this caused by the Intel's BX chipset or this is a timing problem in the Win98SE? I haven't any problems with the Kingston USB Drives before (DTI 1-2GB,DTI plus,Migo) or A-Data 4GB.Or does Kingston something changed in the Flash drives HW? Some new Flash drives from Kingston are working fine like DT101 and DT100 which I tested. Does anybody have a somekind a list of USB Flash drives which are working fine on W98SE?

Hello I have workin Win95OSR2.5 including patches to handle USB devices.When I connect a USB flash drive,I can access it without problems,but when I disconnect it and plug it again,the system won't access it and I can't eighter see it in the system.I have looked at the device manager,when I plug the flash drive for the first time,in device manager under USB Controller root I can see two devices like USB Mass Storage Device and USB Mass Storage Interface.When I disconnect the flash drive and reconnect,I can see in device manager in the USB Controller root only USB Mass Storage Device.The USB Mass Storage Interface doesn seem to reload. Does anybody know what is this caused by,why the flash drive is not able to access when reconnected? HW used is AMD-K6-III with Asus TX97-X Thanks for advice