Wesmosis Posted July 29, 2005 Share Posted July 29, 2005 hey guyzI donno , last couple of dayz i'm having a rough time with : HDD + CD Writer Driver + IDE CablesI solved my (Samsung HDD Problem; Delayed Write Failed) which I posted itbut now I'm facing a problem with my LG CD-R/RW Driver 24x,I bought a real good IDE Ultra DMA Cable (MSI) with the 80 wire - 80 pinsI'm connecting both the CD RW and the HDD into Secondary IDE Channelthe CD WR is Master , the HDD is Slavethe HDD is working fine now with the Ultra DMA Mode 3, but the CD RW always in PIO mode! which causing me a problem whenever I Burn or Reading from the CD, everthing become slow and Sluggish!............I read the Manual and the Officla Site of LG it Said:Data Transfer Rate:Burst ATAPI (Which I don't know what it means!);16.67 MBs /s (PIO Mode4)16.67 MBs /s (Multi DMA - Mode 2)& from little experince : PIO is Evil! , Ultra DMA is Good!so how can I turn my LG Writer into DMA?!I'm waiting for my heroS! thanx guys in advanced Link to comment Share on other sites More sharing options...
Zxian Posted July 29, 2005 Share Posted July 29, 2005 Your best bet is to try to switch around the connections for your devices in as many different ways as possible.Does your BIOS allow you to check the transfer mode of your devices?You could also try uninstalling the device in Device Manager and letting the system find it again on boot. Link to comment Share on other sites More sharing options...
ravashaak Posted July 29, 2005 Share Posted July 29, 2005 If the above advice doesn't work for you, check to see if there's an updated firmware revision for your burner. This cured a similar problem for me with my Plextor PX-708A DVD burner. - ravashaak Link to comment Share on other sites More sharing options...
Wesmosis Posted July 29, 2005 Author Share Posted July 29, 2005 @Zxainok I'll give it a shot , & then see if it switchs to (DMA-MODE)@Ravashakexcuse me, where can I find the update for the firmware revision for my burner?LG CD-R/RW Drive 24x GCE-8240B Link to comment Share on other sites More sharing options...
jcarle Posted July 29, 2005 Share Posted July 29, 2005 I'd recommend the following (some of it was already suggested above, but you know...):Put your hard drives on one cable on the primary IDE channel, and your optical drives on another cable on the secondary IDE channel.Make sure that both of your cables are 80-wire cables.Update your motherboard's BIOS to the latest version and update your optical drive's BIOS to the latest version.Make sure that your BIOS is set to Auto and that UDMA is enabled.Make sure that you have the latest chipset and IDE drivers for your motherboard installed. Link to comment Share on other sites More sharing options...
tester_pedro Posted July 29, 2005 Share Posted July 29, 2005 try to uninstall the problematic device in Device manager and then the Secondary channel. then restart. after restart should the devices automaticly be reinstalled.XP put a device into PIO mode if a couple of errors by communitating appears and what I wrote is a workaround. Link to comment Share on other sites More sharing options...
Wesmosis Posted July 29, 2005 Author Share Posted July 29, 2005 (edited) ok guyz........ 1- I can't put my HDD on the Primary IDE Channel since I got 2 HDDs connected there! so the only free space left is to connect the 160 GBs HDD with my CDRW!2-I checked my BIOS settings.....ALL DMA is AUTO3- My award BIOS is the latest version , I can't find this called (firmware)4- I tried Uninstalling the CDRW........nothing new happen5- I'll try Uninstalling the whole Secondary Channel IDE, maybe it works6- I read somewhere on the net that whenever you connect your CDRW with other HDD, it will be PIO Defenitly! is that true? can anyone see his CDRW which connected with a HDD and tell us which Mode it is?! Edited July 29, 2005 by Wesmosis Link to comment Share on other sites More sharing options...
jcarle Posted July 29, 2005 Share Posted July 29, 2005 Try starting your computer without your 160GB connected to see if that fixes your PIO issue, if so, then you have your answer. Link to comment Share on other sites More sharing options...
Wesmosis Posted July 29, 2005 Author Share Posted July 29, 2005 heyyyyyyyyyyyyyyyyyyyyyyyyy!man! the Fifth Step was the One:5- I'll try Uninstalling the whole Secondary Channel IDE, maybe it works****! I knew MSFN can rock! LOLThanx Icarle and I'll try it later , Thanx Tester Pedro for this wonderful trickcheck this Out:Byeeeeeeeeeeee Link to comment Share on other sites More sharing options...
tester_pedro Posted July 30, 2005 Share Posted July 30, 2005 heyyyyyyyyyyyyyyyyyyyyyyyyy!man! the Fifth Step was the One:5- I'll try Uninstalling the whole Secondary Channel IDE, maybe it works****! I knew MSFN can rock! LOLThanx Icarle and I'll try it later , Thanx Tester Pedro for this wonderful trickcheck this Out:Byeeeeeeeeeeee<{POST_SNAPBACK}>You are welcome. Link to comment Share on other sites More sharing options...
dEXE Posted July 31, 2005 Share Posted July 31, 2005 Maybe this will help next time...When CD drive have trable to read some CD's, windows disable DMA, and if this hapen do this:Re-enable DMA using the Registry EditorRun REGEDIT. Go to the following key:HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}It has subkeys like 0000, 0001, 0002, etc. Normally 0001 is the primary IDE channel, 0002 the secondary, but other numbers can occur under certain circumstances. You have to go through these subkeys and check the DriverDesc value until you find the proper IDE channel.Delete MasterIdDataChecksum or SlaveIdDataChecksum, depending on whether the device in question is attached as master or slave, but it can't actually hurt to delete both. Reboot. The drive DMA capabilities will be redetected.Open Device Manager again and check whether the device is now actually using DMA mode. If so, congratulations, you've made it (at least until the next time Windows disables DMA). Link to comment Share on other sites More sharing options...
jcarle Posted July 31, 2005 Share Posted July 31, 2005 (edited) We should open up a 1-900-MSFN-SUPPORT line... Edited July 31, 2005 by jcarle Link to comment Share on other sites More sharing options...
MCSE Posted August 4, 2005 Share Posted August 4, 2005 very good trick,but what isa different between DMA MODE and MULTI-WORD MODE? Link to comment Share on other sites More sharing options...
tester_pedro Posted August 4, 2005 Share Posted August 4, 2005 very good trick,but what isa different between DMA MODE and MULTI-WORD MODE?<{POST_SNAPBACK}>here are some usefull information: http://www.wtysoft.com/ataref.htm Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now