Jump to content

ma3x

Member
  • Posts

    5
  • Joined

  • Last visited

  • Donations

    0.00 USD 
  • Country

    Poland

About ma3x

Profile Information

  • OS
    Windows 10 x64

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

ma3x's Achievements

0

Reputation

  1. Thank you for your help. Hdd is working!!! All what i had to do was keeping the READ pins shorted and turned drive pwr on. Terminal stopped at "(P) SATA Reset" for a while so i removed jumper that was shorting the pins and drive console started to operate normally. After connecting the drive to pc, all partitions were visible under windows 10 partition manager and under EASEUS Partition Master. Boot 0x40M Spin Up[0x000246DF] Trans. Rst 0x40M MC Internal LPC Process Spin Up (P) SATA Reset MediaPartition: Host LBA Length Disc LBA Length Start Cyl Head Media Partition 00000000 0099A140 00000000 00133428 00000000 00000000 MC 00000000 0098A000 00000000 00131400 00000000 00000000 MSP 00991A80 00000C40 00132350 00000188 00000206 00000005 User Partition 0099A140 00133428 000001FB 00000005 MCMainPOR: Start: Check MCMT Version: Current MCMainPOR: Non-Init Case MC Seg Disc and Cache Nodes: 40134924 40132A34 Seg Write Preamble VBM start: 000011B2 end: 000011D9 Footer - start: 000011DB end: 00001202 Seg Read Preamble VBM - start: 00001204 end: 0000122B Footer - start: 0000122D end: 00001254 Reconstruction: MCMT Reconstruction Start Max number of MC segments 22E0 Nonvolatile MCMT sequence number 0025D079 [RSRS] 17DD DiscLba 000D0CDC RW_RTL FFFFFFFF [SW] 0002 [SW] 0003 [SW] 0004 [SW] 0005 [SW] 0006 [SW] 0006 [SW] 0006 [SW] 0007 [SW] 0008 [RSRS] 17E6 DiscLba 000D11C8 RW_RTL FFFFFFFF [SW] 0008 [SW] 0008 [SW] 0008 Reconstruction: Completed 1: Reconstruction occurred [MCMTWS] MCMainPOR: MCTBufferPtr->Header.MCStateFlagsDisc = 00000041 MCMainPOR: MCTBufferPtr->Header.MCTStateFlags = 0000002A MCMainPOR: MCStateFlags = 00000041 MCMainPOR: Feature Enabled... MSP MainPOR: MSP Init Metadata Buf Bytes/VBM 00000210 DBA Base 40000000 Metadata size in bytes 0040 Num Segments 0062 Logical Sector Alignment 00000000 MSP Reconstruction MSP Read ScratchPad Section 0000 DiscLBA 00132350 BlkSize 00000C40 Num Segments 00000062 DiscLba 00132350 RW_RTL 000F4240 No valid segments found MSP MSP Main Store Verify Reconstruction Status 10003000 Reconstruction Status 00003000 MSP Init ScratchPad on DiscDiscLBA 00132350 DiscSize 00000188 PhyBlkLBA 00991A80 BlkSize 00000C40 Write MSP Segment PhyBlkLBA 00991A80 BlkSize 00000C40 DiscLba 00132350 RW_RTL FFFFFFFF MSP MainPOR: Complete MSP MainPOR: Feature Enabled... ScratchPad restore NOT required [SR] 0008 [SR] 0006 [SR] 0005 [SR] 0004 [SR] 0004 [SR] 0004 [SR] 0004 [SR] 0004 [SR] 0003 [SR] 0003 [SR] 0002 [SR] 0001 [MCMTWS]
  2. Many of these links do not work, but my version of pcb has rev.B and does not differ anything with the one in the picture (rev.A), the tracks on the plate run identically and I think that the rev.A from the foto is nothing different.
  3. Thank you for your help and commitment. My English is weak so I ask to be sure. I will translate this into my language and try it. In the worst case scenario, I will throw the disk into the basket. The disc has been lying there for 2 years so it will be great as it will be great because I have something on it but I can not remember what it is If it fails, it will be difficult. Anyway, thank you and best regards. I apologize for mistakes in text but I am using Google translator
  4. Do You mean this: HI EVERYBODY I HAVE FIXED THIS 2TB LP SEAGATE DRIVE.YOU DONT NEED TO SCARED JUST FIND OUT THOSE TWO PINS TO SHORT.SHORT IT FOR A WHILE AND YOU WILL GET READY IN STATUS BAR.THAN JUST POWER DOWN AND POWER ON YOU WILL GET YOUR DRIVE BACK .I AM STILL USING THIS DRIVE.DONT WORRY WHEN YOU HEARD SOME TYPICAL SOUND WHEN YOU SHORTING THESE PINS.ITS A PART OF THIS PROCESS. KIND ATTN:PLS REFER THIS PIC GIVEN BELOW IF YOU HAVE SAME DIAG ERROR AS PEOPLE SHOWN HERE IN TERMINAL LOG. THE PEOPLE WHO HAS NEW HARD DRIVE AND FIRST TIME PROBLEM OF NOT DETECTING BY BIOS OR BUSY IN TERMINAL OR DOING NO TERMINAL JOB SHOULD FOLLOW ONLY OLDER 7200.11 SYSTEM.PLACE ONE VISITING CARD JUST UNDER CONNECTION OF HEAD CONNECTOR WHICH CONNECTED TO PCB AND THAN GO TO TERMINAL /2 F32>Z spin down NOW REMOVE THE VISITING CARD AND TIGHT THE SCREWS THAN, F32>U SPIN UP CTRL+Z F3T>i4,1,22 clear g-list F3T>/1 F31>N1 smart cleared just power down power on you can see your hdd is back with all data DONT GIVE m0,2,2,,,,,22 m,6,2,,,,,22 OR ANY SAME ALL THE TERMINAL LOG AS YOU CAN SEE REGARDING "No HOST FIS-ReadyStatusFlags 0002A1E1" THIS IN THIS POST ARE VICTIM OF THIS M-FORMAT COMMAND AS PER MY KNOWLEDGE EVEN I HAVE MADE SAME MISTAKE. HERE I HAVE ATTACHED ANOTHER JPG WITH CIRCLE ON POINT TO BE SHORTED ALL THE BEST. I HAVE WRITTEN WHAT I HAVE DONE.AND I GET SUCCESS EVEN JUST BEFORE THIS POST I HAVE APPLIED ON ANOTHER SAME DRIVE.SIMPTOMS HDD BECOMES INITIALIZED NO NOISE SMOOTH SPINING AND LOG FILE YOU ALL HAVE.THE PROBLEM START WITH YOU PEOPLE APPILED V4 V1 ANm format you will get this errror.So all the best to all and enjoy and share your success with others . To make a short circuit on these pins?
  5. Hi. I have problem with my seagate drive. Please Help! I try everything what i find on internet but nothing helps. Drive is Seagate Baracuda Green 2000GB ST2000DL003 S/N: 5YD7SKL6 P/N: 9VT 166-302 F/W: CC3C Date: 12326 Site: WU I connect this drive to HDD terminal and get this: Boot 0x40M Spin Up[0x000246DF] Trans. Rst 0x40M MC Internal LPC Process Spin Up (P) SATA Reset MediaPartition: Host LBA Length Disc LBA Length Start Cyl Head Media Partition 00000000 0099A140 00000000 00133428 00000000 00000000 MC 00000000 0098A000 00000000 00131400 00000000 00000000 MSP 00991A80 00000C40 00132350 00000188 00000206 00000005 User Partition 0099A140 00133428 000001FB 00000005 MCMainPOR: Start: Check MCMT Version: Current MCMainPOR: Non-Init Case MC Seg Disc and Cache Nodes: 40134924 40132A34 Seg Write Preamble VBM start: 000011B2 end: 000011D9 Footer - start: 000011DB end: 00001202 Seg Read Preamble VBM - start: 00001204 end: 0000122B Footer - start: 0000122D end: 00001254 Reconstruction: MCMT Reconstruction Start Max number of MC segments 22E0 Nonvolatile MCMT sequence number 0025D088 [RSRS] 17E9 DiscLba 000D136C RW_RTL FFFFFFFF Reconstruction: Completed 1: Rst 0x40M MC Internal LPC Process Spin Up LED:000000BD FAddr:00009E13 Terminal is blocked. How fix it? Please help. I have foto on this drive. PS: sorry for my English. Google helped
×
×
  • Create New...