Jump to content

my77stang

Member
  • Posts

    19
  • Joined

  • Last visited

  • Donations

    0.00 USD 
  • Country

    United States

Everything posted by my77stang

  1. I don't understand why you guys are shelling out extra money for the serial to TTL converters, battery packs, and whatnots. the CA-42 cable works like a charm, cost less than 6.00 with shipping, and eliminates so much guesswork. i posted the ebay seller i used on the previous page, so you know where to get one that works for sure. 36 pages deep and it still sounds so complicated - when really it is not once you know what needs to be done.
  2. here, just to get this on the current page - and to update a few things to make it easier for people to understand - i will repost this from page 27 in a modified form....
  3. if you remove the entire PCB you'll see the connector between the drive and the PCB (not the one that goes over to the center of the drive where the motor is). that is the connector i blocked with a paper business card, then screwed down the rest of the PCB just enough to make sure the board was grounded to the drive (don't know if that mattered). following the steps on page 27 from Aviko, i had success once i realized i needed to remove the business card before spinning the drive back up.
  4. I finally got my CA-42 cable, hooked everything up and got the exact same error. PLEASE someone help me im going nuts! *edit* hey WolfDie, I just realized before we enter the "U" command (spin up) we need to reconnect the PCB to the drive. I was able to do everything, going to reboot and see what happens now. I am using the directions as given by Aviko on page 27 (I think it was) *2nd edit* Just rebooted, flashed drive to updated firmware, rebooted, and everything is up and running. THANK YOU EVERYONE who helped make this fix available!!!!!!!!!!!!!
  5. Aviko, Thank you for the clarified post on page 27 - that should be on the first page so people can find it and have the correct information. I'll let you know how it works out for me, hopefully my data cable will be here tomorrow.
  6. so officially, this is the best (safest) way to make it work if you have the BSY error.... right? I've highlighted the actual commands to be typed in red. if i missed anything here, please requote this and correct it. with all this gibberish it gets hard to figure out exactly what needs to be done and im terribly afraid i'll screw something up (probably alot of us like that). and if i understand everything correctly, even though it says "user partition format" it is not actually messing up partitions or data. correct?
  7. great, so after all the work to bring our drives back (still waiting on the cable to fix mine) they are crapping out again?
  8. aviko, If you are so unhappy with the guide that was originally laid out PLEASE give us a list of commands you recommend to safely fix our drives. I have the BSY error, and should be getting my cell phone cable any day. I want to make sure I do not loose all my data. Thanks
  9. i believe you both know alot more than most of us - if you can put your heads together maybe there can be a solution that is agreed upon by both of you.... and be the best route for us all to take.
  10. i was thinking it only needed one ground. ike taking the usb ground wire, stripping some and wrapping around a screw then screwing it into the mounting holes on the side of the drive. yeah, the 2nd PSU will be a floater, but honestly i could use the system's PSU to power the drive if it helps.
  11. so, like a jumper wire from the ground on a molex plug from one PSU to the other? ir would i be better to take the ground wire from the cell phone cable and ground it out to the body of the HD?
  12. i still dont think i got a reply on this and i even posted boobies, so i'll ask again =) ^ is that correct?
  13. thanks for the idea's about making the rx/tx cable. can anyonce clarify this part for me? i just want to make sure im 100% clear on this. there's not going to be too many volts going thru the tx/rx lines (like 5v from the usb port or anything), and i dont need to worry about any kind of ground wire in the cell phone cable right? i appreciate all your guys help, so in return i give you boobies
  14. just to clarify when using the cell phone cable method, all i need is the tx and rx cables from it right? then plug the HD into any sata power cable (i have a 2nd PSU i can use for this) also i saw someone had a little white plug in their HD for the tx and rx wires so the plugs stay on those little pins. anyone know where to find a plug that small? i *think* header cables (like found in a computer case) are too big.
  15. we need to turn echo off before entering in all that code as posted on page 1 right?
  16. nah it didnt have one, like i said i chopped the cable to see and it was a no-go. just got back from walmart and they had nothing either. i'll be going to best buy tomorrow to see what they have. *edit* screw it, i just ordered a CA-42 with a driver disc and shipping (from a US seller too) on ebay for less than 6.00 i'll post my results to add to the list once im done.
  17. yeah my original idea was scrapped once i actually read thru all 21 pages. i chopped up an old LG VX9800 cable i had and it was a no-go. I'm gonna go to wal-mart and see if they have any cables that will work (3120, dku-5, ca-42, ca-45) Maybe i'll get lucky and we'll have some freeware from grad soon (honestly, i'd pay at least 10 bucks for it if i had to LOL)
  18. Gradius I registered just to let you know your a hero among men. My drive is currently down and I believe its the BSY error as it will no detect in BIOS. When it first failed the machine wouldn't even boot past the initial splashscreen with the drive hooked up. After hours of swapping things around and pulling my hair out the computer actually start now with the drive hooked up but still does not detect the drive. I have a PCI diagnostic card from Ultra-X (not cheap btw) and it shows there is something hooked up to that particular SATA port but cannot pull any info from the drive. I went to my local radioshack today hoping they would carry or would be able to order the items i need to make this little setup, but they had nothing and don't even carry paper catalogs now - they just search on their website which pointed me to retarded things like digital cameras when i searched for the required parts. If there is any interest from the community, I would consider ordering a few of the RS232 to TTL boards, some small project boxes, battery holders, batteries, an on/off switch, and leads to make a few of these in a nice neat little package. I'm sure there are alot of people who would like to make these things but are intimidated by a soldering iron. if you can pound out that program to make it a no brainer for people to perform the functions i would paypal you 1 million dollars in wooden mexican pesos
×
×
  • Create New...