ripken204 Posted February 2, 2006 Author Share Posted February 2, 2006 use the bios! you will also notice that while under load, cpuz will give a higher voltage than at idle, that higher voltage is closer to the correct voltage. for the voltage, set it to 1.5v right now and see how high u can get. and leave the ram divider at 1:2 Link to comment Share on other sites More sharing options...
Porn Loader Posted February 2, 2006 Share Posted February 2, 2006 use the bios! you will also notice that while under load, cpuz will give a higher voltage than at idle, that higher voltage is closer to the correct voltage. for the voltage, set it to 1.5v right now and see how high u can get. and leave the ram divider at 1:2yea, i just need more time to play. I took today off and still ended up at the office for a couple of hours. its been acouple of months since ive tweaked w/ th dfi mem settings. time for some reading! i was kinda hoping for 2.6 at default w/o any dicking around. lady luck is not on my side i guess. Link to comment Share on other sites More sharing options...
gdogg Posted February 2, 2006 Share Posted February 2, 2006 I just got my new machine up, currently, I got my opteron 165, 1.8Ghz default @ 2.6 Ghz stable (FX 60) going for 2.8 Ghz Link to comment Share on other sites More sharing options...
Clint Posted February 2, 2006 Share Posted February 2, 2006 well,..hehe..I did provide you with meausured voltage directly on board with a Multimeter...but please speculate on.. Link to comment Share on other sites More sharing options...
Porn Loader Posted February 3, 2006 Share Posted February 3, 2006 well,..hehe..I did provide you with meausured voltage directly on board with a Multimeter...but please speculate on.. yea but that chart doesnt list what the bios reads at x amount of vcore. i know the things overvolt a touch when under load, but i don't remember it doing this w/ my 4000+ sd. Link to comment Share on other sites More sharing options...
ripken204 Posted February 3, 2006 Author Share Posted February 3, 2006 I just got my new machine up, currently, I got my opteron 165, 1.8Ghz default @ 2.6 Ghz stable (FX 60) going for 2.8 Ghzyou're where i am right now, but ive got a 10x mult it would be nice to get 2.8 but i doubt you will, 2.7 is usually the max. dont use too high of a voltage tho, anything over 1.55v is getting risky, im a 1.475 so im not gunna worry. Link to comment Share on other sites More sharing options...
Clint Posted February 3, 2006 Share Posted February 3, 2006 (edited) Edited February 10, 2006 by Clint Link to comment Share on other sites More sharing options...
gdogg Posted February 8, 2006 Share Posted February 8, 2006 (edited) @ripken204I am giving it 1.6Vdue to the fact I am using mushkin redline @ 3.6Vbasically, venice core and newer, need to have 1/2 the vcore of the vmem, or you can cause serious damage to your processor.I know I am not there, but a 1.45 would hurt it more than the 1.6 is. but no way am I gonna give it 1.8 lolhttp://www.xtremesystems.org/forums/showthread.php?t=79509 Edited February 8, 2006 by gdogg Link to comment Share on other sites More sharing options...
ripken204 Posted February 8, 2006 Author Share Posted February 8, 2006 just watch your temps, you are getting risky at 1.6vhow high is your overclock? Link to comment Share on other sites More sharing options...
gdogg Posted February 8, 2006 Share Posted February 8, 2006 (edited) same as I said b4, 290X9 on a 9/10 for the memoryso, 2610MHZidle 27load 43load after 10 hours of prime95 48 Edited February 8, 2006 by gdogg Link to comment Share on other sites More sharing options...
ripken204 Posted February 8, 2006 Author Share Posted February 8, 2006 you should definetly try to overclock more, you should be able to get 2.7 or over with that much voltage. and why the divider with that ram? i have the next level below you as far as mushkin ram goes and mines is running at 260 just fine Link to comment Share on other sites More sharing options...
gdogg Posted February 8, 2006 Share Posted February 8, 2006 261 is 522it wont even do 26302610 is as far as it goesthe bios on the expert boards suck, honestly, only the origional bios works over 3.3V memory, all the updates dont.until they fix these probs, I cant do much, if its bios related Link to comment Share on other sites More sharing options...
ripken204 Posted February 8, 2006 Author Share Posted February 8, 2006 wow, that sucks. how about your cpu tho, have you ever tried 2.7? Link to comment Share on other sites More sharing options...
gdogg Posted February 9, 2006 Share Posted February 9, 2006 yah, tried 2.7 got the memory stable as .... and still no gono volts on anything mad any difference, I am pretty sure I got the max OCI will try burn-ins, but not yet, i got other stuff to do. Link to comment Share on other sites More sharing options...
ripken204 Posted February 9, 2006 Author Share Posted February 9, 2006 im running 2.6 with mines, i think that i can do 2.7 with mine with just under 1.6v . i tried it with prime and i stopped after about an hour b/c the temps were starting to get high, if i had watercooling then im sure that i'de be able to do it.try 265x10 and see if that works Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now