Jump to content
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble
Strawberry Orange Banana Lime Leaf Slate Sky Blueberry Grape Watermelon Chocolate Marble

MSFN is made available via donations, subscriptions and advertising revenue. The use of ad-blocking software hurts the site. Please disable ad-blocking software or set an exception for MSFN. Alternatively, register and become a site sponsor/subscriber and ads will be disabled automatically. 


Gradius2

The Solution for Seagate 7200.11 HDDs

Recommended Posts

These are "separate" issues.

The BSY or LBA0 issues are the result of *something* that causes the disk firmware to enter a *loop* of some sort.

The "cure" is a method/procedure to exit this *loop*.

Bad sectors may develop for several reasons that have nothing to do with the above (and that cannot be fixed).

The fact that you updated the firmware (which is never recommended and definitely NOT suggested in the case of flashing a Seagate firmware over a HP one :no:) may be part of the cause of the bad sectors, but not necessarily.

That disk is now "gone for good", if it has developed bad sectors (and continues developing them).

If you have on it data that you wish to recover :ph34r:, you should have NOT updated the firmware, and in any case now you may look for professional recovery services.

If you managed to recover the data on it, it's time to throw the stupid disk in the dustbin and buy a newer one :(.

jaclaz

Share this post


Link to post
Share on other sites

These are "separate" issues.

The BSY or LBA0 issues are the result of *something* that causes the disk firmware to enter a *loop* of some sort.

The "cure" is a method/procedure to exit this *loop*.

Bad sectors may develop for several reasons that have nothing to do with the above (and that cannot be fixed).

The fact that you updated the firmware (which is never recommended and definitely NOT suggested in the case of flashing a Seagate firmware over a HP one :no:) may be part of the cause of the bad sectors, but not necessarily.

That disk is now "gone for good", if it has developed bad sectors (and continues developing them).

If you have on it data that you wish to recover :ph34r:, you should have NOT updated the firmware, and in any case now you may look for professional recovery services.

If you managed to recover the data on it, it's time to throw the stupid disk in the dustbin and buy a newer one :(.

jaclaz

Thank you for reply...

On HP24 firmware was also bad sectors,first problem was that bios dont see the drive,but i was able to install system on it,and then i run HD Sentinel,and see about 2000 bad sector,later i found this solution,but first i updated the firmware to SD1A,i was hoping that bad sectors are gone,but not.Then i try the fix of BSY and LBA0,it was successfully,turn on hard drive,run sentinel,healt was 100%,performance also,then again updated firmware,and later,bad sectors return...When i run surface test it's all ok,no sign of bad sectors,but sentinel show's it...

I was hoping that I would solve the problem and I was persistent, but I no longer have the nerves!

I have no data on it,now i'm selling the drive!

Share this post


Link to post
Share on other sites

Wait a minute.

If BOTH the Seagate (and NOT any other tool) Diagnostic tools (Seatools) run the short and long test successfully, then your disk is fine and HD sentinel is wrong.

jaclaz

Share this post


Link to post
Share on other sites

Wait a minute.

If BOTH the Seagate (and NOT any other tool) Diagnostic tools (Seatools) run the short and long test successfully, then your disk is fine and HD sentinel is wrong.

jaclaz

I think the last time I worked the tests, they were ok .. then why would the sentinel showed bad sectors...

I'll do it test again during the day,and take screenshot to see...

Share this post


Link to post
Share on other sites

Though when it comes to design reliable disk drives the good engineers at Seagate do suck a bit ;) and the way this particular model issues were mis-managed by the technical support sucks BIG, but they actually know what is inside their hard disks (I mean, they designed and manufactured them, they anyway know more - and very, very often won't tell - than anyone else on the specific topic).

The Seatools are for Seagate a "key" app, if either the short or long test fails, it will produce a code that will entitle you (if the disk drive is still under warranty) to have a replacement unit.

Though it is of course possible that because of the above the tool is maliciously tuned to make drives appear more healthy than they really are :w00t::ph34r:, I doubt that this is the case, as a matter of fact the common experience on this thread shows that disks that did not pass the test were anyway largely accessible and functional.

HD sentinel is a third party "generic" tool that uses the monitoring of the SMART attributes of the disk to "predict" failure.

While the approach:

http://www.hdsentinel.com/smart/index.php

is seemingly more "sound" than the "plain" check for SMART thresholds, but it is anyway a "theoretical model", seemingly nice, but only assertedly and theoretically more accurate than "plain" check.

The SMART in itself is not accurate at all, and to all practical effects it has not any relevant increase in accuracy than flippism, see:

http://www.msfn.org/board/topic/170237-which-drive-sould-i-get/

http://www.msfn.org/board/topic/153191-does-copying-several-giga-bytes-on-a-daily-base-screw-the-hard-drive/

There is not any evidence (AFAIK) that the HDsentinel method is accurate or "more accurate" than anything else, the only thing that you can say for sure of the results is that it is "more conservative", .i.e. it will start crying (sometimes crying Wolf! ;)) much earlier than a "plain" SMART monitoring tool, in their own words (same source as above):

According to this number, the health is disquieting. By default, this software would alert the user if the health value is as low as this number. By selecting the correct evaluation method and the correct alert levels, it is possible to predict failure long before the catastrophe. The owner of this hard disk could prevent data loss if he'd install this software before.

A low health value alone does not neccessary mean that the hard disk will surely die in the near future (to verify this, a complete (hardware) examination is required), but there is a real chance for failure. The problem of the hard disk described above can not be easily detected but as we can see, there were some signs in the S.M.A.R.T. attributes. Other hard disks with other problems may work for a long time, months or years (even if they have lower health value). Problems caused by a short period (for example, too hot environment or an incorrect power supply) will not disappear. But after fixing the reasons of such problems (using a heatsink, fan or replacing the power supply), the hard disk lifetime can be extended. Anyway, it is recommended to examine the status of these hard disks constantly or regulary and to use them as secondary data storage only. Users should make sure that their important and valuable files are stored on an other hard disk also (with a higher "health" value).

jaclaz

Share this post


Link to post
Share on other sites

Though when it comes to design reliable disk drives the good engineers at Seagate do suck a bit ;) and the way this particular model issues were mis-managed by the technical support sucks BIG, but they actually know what is inside their hard disks (I mean, they designed and manufactured them, they anyway know more - and very, very often won't tell - than anyone else on the specific topic).

The Seatools are for Seagate a "key" app, if either the short or long test fails, it will produce a code that will entitle you (if the disk drive is still under warranty) to have a replacement unit.

Though it is of course possible that because of the above the tool is maliciously tuned to make drives appear more healthy than they really are :w00t::ph34r:, I doubt that this is the case, as a matter of fact the common experience on this thread shows that disks that did not pass the test were anyway largely accessible and functional.

HD sentinel is a third party "generic" tool that uses the monitoring of the SMART attributes of the disk to "predict" failure.

While the approach:

http://www.hdsentinel.com/smart/index.php

is seemingly more "sound" than the "plain" check for SMART thresholds, but it is anyway a "theoretical model", seemingly nice, but only assertedly and theoretically more accurate than "plain" check.

The SMART in itself is not accurate at all, and to all practical effects it has not any relevant increase in accuracy than flippism, see:

http://www.msfn.org/board/topic/170237-which-drive-sould-i-get/

http://www.msfn.org/board/topic/153191-does-copying-several-giga-bytes-on-a-daily-base-screw-the-hard-drive/

There is not any evidence (AFAIK) that the HDsentinel method is accurate or "more accurate" than anything else, the only thing that you can say for sure of the results is that it is "more conservative", .i.e. it will start crying (sometimes crying Wolf! ;)) much earlier than a "plain" SMART monitoring tool, in their own words (same source as above):

According to this number, the health is disquieting. By default, this software would alert the user if the health value is as low as this number. By selecting the correct evaluation method and the correct alert levels, it is possible to predict failure long before the catastrophe. The owner of this hard disk could prevent data loss if he'd install this software before.

A low health value alone does not neccessary mean that the hard disk will surely die in the near future (to verify this, a complete (hardware) examination is required), but there is a real chance for failure. The problem of the hard disk described above can not be easily detected but as we can see, there were some signs in the S.M.A.R.T. attributes. Other hard disks with other problems may work for a long time, months or years (even if they have lower health value). Problems caused by a short period (for example, too hot environment or an incorrect power supply) will not disappear. But after fixing the reasons of such problems (using a heatsink, fan or replacing the power supply), the hard disk lifetime can be extended. Anyway, it is recommended to examine the status of these hard disks constantly or regulary and to use them as secondary data storage only. Users should make sure that their important and valuable files are stored on an other hard disk also (with a higher "health" value).

jaclaz

Today I installed Windows on it, then I installed SeaTools and HD sentinel.Sentinel showed 173 bad sectors.Seatools passed the short test, but not long finished properly, I'll try another long test, because my computer went to stand by.

Thank you once again for your reply!

Share this post


Link to post
Share on other sites

Here is the screenshots,that's it,i will no more try to do anything with this hard drive!

Again thank you!

Edited by seg77

Share this post


Link to post
Share on other sites

Here is the screenshots,that's it,i will no more try to do anything with this hard drive!

Again thank you!

I am not sure to understand. :unsure:

The screenshot on the left is seemingly about the "Short" test (and this was passed, good :)).

What about the "Long" test (which is BTW evidently more complete/thorough)?

jaclaz

Share this post


Link to post
Share on other sites

Here is the screenshots,that's it,i will no more try to do anything with this hard drive!

Again thank you!

I am not sure to understand. :unsure:

The screenshot on the left is seemingly about the "Short" test (and this was passed, good :)).

What about the "Long" test (which is BTW evidently more complete/thorough)?

jaclaz

Right now i'm doing the long test,and later i will post the screenshot!

It's strange when i enter the comand in hyperterminal,m0,22,,,,,22 ,and just say some text,formated but no show how much percentage,and successfull,elepsated time 0 and that's it!

Share this post


Link to post
Share on other sites

Test lasted for 30 min, then failed, the computer suddenly rebooted I do not know why, I had to turn it off, then Windows reported the error blue screen.
Right now i'm using this drive,no problems.
I will not attempt to do anything with the hard drive!

Thank's!

Share this post


Link to post
Share on other sites

Test lasted for 30 min, then failed, the computer suddenly rebooted I do not know why, I had to turn it off, then Windows reported the error blue screen.

Right now i'm using this drive,no problems.

I will not attempt to do anything with the hard drive!

Thank's!

Yep :), but all the "combined" reports (including the failure to perform a "Long" test) lead to believe that the disk is having issues, I personally would not EVEN THINK of using it as "System" drive, further use is suggested possibly ONLY as a secondary or tertiary backup.

jaclaz

Share this post


Link to post
Share on other sites

Test lasted for 30 min, then failed, the computer suddenly rebooted I do not know why, I had to turn it off, then Windows reported the error blue screen.

Right now i'm using this drive,no problems.

I will not attempt to do anything with the hard drive!

Thank's!

Yep :), but all the "combined" reports (including the failure to perform a "Long" test) lead to believe that the disk is having issues, I personally would not EVEN THINK of using it as "System" drive, further use is suggested possibly ONLY as a secondary or tertiary backup.

jaclaz

Yes,certainly the problem to the hard disk.

I dont use it anymore,now it's on auction,I hope to get rid of that drive! :)

Thank's again.

Share this post


Link to post
Share on other sites

Yes,certainly the problem to the hard disk.

I dont use it anymore,now it's on auction,I hope to get rid of that drive! :)

I hope you are honest and tell whoever buys it that it has problems?

Cheers and Regards

Share this post


Link to post
Share on other sites

Yes,certainly the problem to the hard disk.

I dont use it anymore,now it's on auction,I hope to get rid of that drive! :)

I hope you are honest and tell whoever buys it that it has problems?

Cheers and Regards

Yes I mentioned what the problem is,if someone does buy!

All the best!

Share this post


Link to post
Share on other sites

I did managed to put the code in hyper terminal till F3 2>U which it prompted error in spinning up...

I tried to redo the whole process again but no prompt in hyper terminal when I press ctrl+z

Any advise to get it back??

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

×