Gradius2 Posted December 20, 2012 Author Share Posted December 20, 2012 Just to report (because is a new record!).A ST2000DM001 just died (out of nothing) with less than 250 working days!And yes, it was using the last FW available to the public.I can't see (or wait) the time when 1TB (and more) SSDs would be cheaper. Link to comment Share on other sites More sharing options...
jaclaz Posted December 20, 2012 Share Posted December 20, 2012 I can't see (or wait) the time when 1TB (and more) SSDs would be cheaper.So that WHEN one of those will fail you will have even LESS chances to recover data from them? We add here to the existing "internal translation" and "G-list" possible issues also the SSD brand new ones, such as "wear leveling" and "garbage collecting". jaclaz Link to comment Share on other sites More sharing options...
Phaenius Posted December 23, 2012 Share Posted December 23, 2012 So far, every storage system can fail. Even Johnny Mnemonic's brain. Link to comment Share on other sites More sharing options...
jaclaz Posted December 23, 2012 Share Posted December 23, 2012 So far, every storage system can fail. Even Johnny Mnemonic's brain.For NO apparent reason :jaclaz Link to comment Share on other sites More sharing options...
elloco4ever Posted December 25, 2012 Share Posted December 25, 2012 HiSorry to bother again but i wanted to ask what does exactly do the last step for fixing the BSY bug. Because ive read the last step and it says:Partition regeneration:F3 T>m0,2,2,,,,,22 (enter)Does this format the hhd? How can i recover the data after doing that?Thanks in advance Link to comment Share on other sites More sharing options...
Phaenius Posted December 25, 2012 Share Posted December 25, 2012 You shouldn't normally need to. Normally the data should be already there after the command and reboot. No need for an additional action. Link to comment Share on other sites More sharing options...
neosource Posted January 4, 2013 Share Posted January 4, 2013 Thank you for this information, I managed to restore a clients hard drive using it Though I found the instructions on this page a little easier to follow and apply (not sure who the author is though). https://sites.google.com/site/seagatefix/HomeThey suggested using a small piece of cardboard to break the connection between the PCB and the head contacts during the spin down phase. I removed the 2 screws near and to the bottom left of the head contacts to allow the cardboard to slide in/out. I also loosened the long screws near the corner edges. After I performed the spin down I then gently removed the cardboard and carefully inserted just the one the screw near the head contacts (helped to use a magnetic tip to position the screw), as that seemed to be the simplest and most efficient way to do it.I had the "Error 1009 DETSEC 0000600" when trying to spin the drive up. A quick fix for me was to simply place a piece of cardboard on top of the PCB (to shield from any electrical discharge) near where the head contacts are and apply some gentle pressure with my finger then try the spin up command again. That allowed me to restore the drive, though cleaning the contacts can also help prevent any further problems. I hope that helps. Link to comment Share on other sites More sharing options...
jaclaz Posted January 4, 2013 Share Posted January 4, 2013 Though I found the instructions on this page a little easier to follow and apply (not sure who the author is though). https://sites.google.com/site/seagatefix/HomeThat guide, though good, is NOT the recommended one, which is this one (as sticked AND pointed to in the READ ME FIRST):http://www.mapleleafmountain.com/seagatebrick.htmlwhich is a more complete one.If you need to use a piece of cardboard to press down the PCB to obtain spin up it means any (or more than one) of three things:you used the cardboard on the head contacts AND the cardboard was a bit too thickthe head contacts were not properly cleanedyou failed to re-tighten appropriately the screws near the contactsThe workaround you used is potentially a VERY dangerous one , what you had was a "bad" contact that you "patched" (possibly only temporarily) by pressing a bit on the PCB.That PCB should be disassembled, contacts cleaned and the "springy effect" of the contacts on the disk be verified, then all screws re-tightened firmly before further use of the disk.jaclaz Link to comment Share on other sites More sharing options...
Phaenius Posted January 4, 2013 Share Posted January 4, 2013 (edited) It is said that what you don't know can't hurt you. Now you made me worry again, jaclaz. I fear I have might tightened the screws too hard. Also, the contacts between PCB, head and motor were so corroded, I wonder how it works. But it does. Edited January 4, 2013 by Phaenius Link to comment Share on other sites More sharing options...
jaclaz Posted January 4, 2013 Share Posted January 4, 2013 It is said that what you don't know can't hurt you. Now you made me worry again, jaclaz. I fear I have might tightened the screws too hard. Also, the contacts between PCB, head and motor were so corroded, I wonder how it works. But it does. JFYI:http://www.crcind.com/wwwcrc/tds/TKC3%20KONTAKT60.PDFhttp://www.crcind.com/wwwcrc/tds/TKC3%20KONTAKTWL.PDFhttp://www.crcind.com/wwwcrc/tds/TKC3%20KONTAKT61.PDFjaclaz Link to comment Share on other sites More sharing options...
Phaenius Posted January 4, 2013 Share Posted January 4, 2013 Too expensive. How about this, found at a local store at about 2.75 euros ? Link to comment Share on other sites More sharing options...
jaclaz Posted January 4, 2013 Share Posted January 4, 2013 I find difficult reading the specs from a (BTW lousy) picture of the spray can.BUT the actual info from the manufacturer:http://www.agchemia.pl/OnlineShop.aspxKONTAKT U a blend of solvents for removing fat, used for cleaning electronic assemblies and electric contacts, removes fat, dirt, old greases and oils, silicones, sulfides and oxides dissolved with KONTAKT S, and all substances remaining after soldering (including rosin). Aerosol cans: 60ml, 300 mlKONTAKT S a preparation for removing oxides and sulfides from electric contacts and for providing protection against corrosion, ensures non-obstructed electricity flow especially in the case of oxidized or worn contacts, can be used in audio products -high and low-frequency, electronic industry and in other places where clean contacts are required. Aerosol cans: 60ml, 300 mlClears how that is as well a three product cycle:de-oxidation <- CRC KONTACT 60 or AG KONTACT Scleaning <- CRC KONTACT WL or AG KONTACT Uprotect <- CRC KONTACT 61 or AG ???jaclaz Link to comment Share on other sites More sharing options...
Phaenius Posted January 4, 2013 Share Posted January 4, 2013 (edited) They'll do anything just to add a letter and taking you more money from your wallet. Same applies to compressed air spray cans. I found one with about 3 euros. I read all sort of theories about them as well.I intended to clean the contacts with this:Universal lotion. Edited January 4, 2013 by Phaenius Link to comment Share on other sites More sharing options...
jaclaz Posted January 4, 2013 Share Posted January 4, 2013 Sure , it's your contacts that are corroded.Please look in a dictionary corroded:http://www.thefreedictionary.com/corrodedand oxidized:http://www.thefreedictionary.com/oxidizedthey are seemingly NOT synonyms of dirty:http://www.thefreedictionary.com/dirtyYou may also want to try some turmeric on them :http://www.peoplespharmacy.com/2011/08/08/curry-spice-for-cuts-and-bruises/jaclaz Link to comment Share on other sites More sharing options...
Phaenius Posted January 4, 2013 Share Posted January 4, 2013 No, that curry spice will only add more granules. Don't think all that cleaning substances are that different. I'm sure a lot of it is just marketing propaganda. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now