ma3x
Content Type
Profiles
Forums
Events
Posts posted by ma3x
-
-
On 4.02.2018 at 3:54 PM, jaclaz said:
Well, the translator did a good enough job, rest assured .
The problem with the shorting is that you need to double and triple check that you identified correctly the read channel pads[1] and then you will need several attempts as reportedly the timing is critical.
Good luck!
jaclaz
[1] Particularly check the given inks on how to identify them if your disk drive has a different PCB revision or version
Many of these links do not work, but my version of pcb has rev.B and does not differ anything with the one in the picture (rev.A), the tracks on the plate run identically and I think that the rev.A from the foto is nothing different.
0 -
Thank you for your help and commitment. My English is weak so I ask to be sure. I will translate this into my language and try it. In the worst case scenario, I will throw the disk into the basket. The disc has been lying there for 2 years so it will be great as it will be great because I have something on it but I can not remember what it is If it fails, it will be difficult. Anyway, thank you and best regards.
I apologize for mistakes in text but I am using Google translator
0 -
Do You mean this:
HI EVERYBODY
I HAVE FIXED THIS 2TB LP SEAGATE DRIVE.YOU DONT NEED TO SCARED JUST FIND OUT THOSE TWO PINS TO SHORT.SHORT IT FOR A WHILE AND YOU WILL GET READY IN STATUS BAR.THAN JUST POWER DOWN AND POWER ON YOU WILL GET YOUR DRIVE BACK .I AM STILL USING THIS DRIVE.DONT WORRY WHEN YOU HEARD SOME TYPICAL SOUND WHEN YOU SHORTING THESE PINS.ITS A PART OF THIS PROCESS.
KIND ATTN:PLS REFER THIS PIC GIVEN BELOW IF YOU HAVE SAME DIAG ERROR AS PEOPLE SHOWN HERE IN TERMINAL LOG.
THE PEOPLE WHO HAS NEW HARD DRIVE AND FIRST TIME PROBLEM OF NOT DETECTING BY BIOS OR BUSY IN TERMINAL OR DOING NO TERMINAL JOB SHOULD FOLLOW ONLY OLDER 7200.11 SYSTEM.PLACE ONE VISITING CARD JUST UNDER CONNECTION OF HEAD CONNECTOR WHICH CONNECTED TO PCB AND THAN GO TO TERMINAL /2
F32>Z
spin down
NOW REMOVE THE VISITING CARD AND TIGHT THE SCREWS THAN,
F32>U
SPIN UP
CTRL+Z
F3T>i4,1,22
clear g-list
F3T>/1
F31>N1
smart cleared
just power down
power on
you can see your hdd is back with all data
DONT GIVE m0,2,2,,,,,22 m,6,2,,,,,22 OR ANY SAME
ALL THE TERMINAL LOG AS YOU CAN SEE REGARDING "No HOST FIS-ReadyStatusFlags 0002A1E1" THIS IN THIS POST ARE VICTIM OF THIS M-FORMAT COMMAND AS PER MY KNOWLEDGE EVEN I HAVE MADE SAME MISTAKE.
HERE I HAVE ATTACHED ANOTHER JPG WITH CIRCLE ON POINT TO BE SHORTED ALL THE BEST. I HAVE WRITTEN WHAT I HAVE DONE.AND I GET SUCCESS EVEN JUST BEFORE THIS POST I HAVE APPLIED ON ANOTHER SAME DRIVE.SIMPTOMS HDD BECOMES INITIALIZED NO NOISE SMOOTH SPINING AND LOG FILE YOU ALL HAVE.THE PROBLEM START WITH YOU PEOPLE APPILED V4 V1 ANm format you will get this errror.So all the best to all and enjoy and share your success with others .
To make a short circuit on these pins?
0 -
Hi. I have problem with my seagate drive. Please Help! I try everything what i find on internet but nothing helps.
Drive is Seagate Baracuda Green 2000GB ST2000DL003
S/N: 5YD7SKL6
P/N: 9VT 166-302
F/W: CC3C
Date: 12326 Site: WU
I connect this drive to HDD terminal and get this:
Boot 0x40M
Spin Up[0x000246DF]
Trans.Rst 0x40M
MC Internal LPC Process
Spin Up
(P) SATA ResetMediaPartition:
Host LBA Length Disc LBA Length Start Cyl Head
Media Partition 00000000 0099A140 00000000 00133428 00000000 00000000
MC 00000000 0098A000 00000000 00131400 00000000 00000000
MSP 00991A80 00000C40 00132350 00000188 00000206 00000005
User Partition 0099A140 00133428 000001FB 00000005MCMainPOR: Start:
Check MCMT Version: Current
MCMainPOR: Non-Init Case
MC Seg Disc and Cache Nodes: 40134924 40132A34
Seg Write Preamble VBM start: 000011B2 end: 000011D9
Footer - start: 000011DB end: 00001202
Seg Read Preamble VBM - start: 00001204 end: 0000122B
Footer - start: 0000122D end: 00001254
Reconstruction: MCMT Reconstruction Start
Max number of MC segments 22E0
Nonvolatile MCMT sequence number 0025D088
[RSRS] 17E9 DiscLba 000D136C RW_RTL FFFFFFFF
Reconstruction: Completed 1:
Rst 0x40M
MC Internal LPC Process
Spin Up
LED:000000BD FAddr:00009E13Terminal is blocked. How fix it? Please help. I have foto on this drive.
PS: sorry for my English. Google helped
0 -
Hi everyone
0
Seagate ST2000DL003 unvisible on system
in Hard Drive and Removable Media
Posted · Edited by ma3x
Thank you for your help.
Hdd is working!!!
All what i had to do was keeping the READ pins shorted and turned drive pwr on.
Terminal stopped at "(P) SATA Reset" for a while so i removed jumper that was shorting the pins and drive console started to operate normally.
After connecting the drive to pc, all partitions were visible under windows 10 partition manager and under EASEUS Partition Master.